Anti Slip Clear Sealer 2.5L Mid Gloss Finish Floor Sealer

Anti Slip Clear Sealer 2.5L Mid Gloss Finish Floor Sealer

Protecta-Coat Anti Slip is an exceptionally hard wearing Polyaspartic two-pack resin coating, which will protect your floors for the long term and offers a slip resistant finish.

1. Protects coloured and decorative coatings from heavy wear and tear
2. Can be applied at temperatures ranging from -10°C to +30°C.
3. Excellent chemical resistance, thus enhancing workplace safety
4. Suitable for internal and external use
5. Finely textured slip resistant finish

Use in a multitude of areas ranging from warehouses and showrooms to walk-in fridges and exterior car parking areas. Externally it will resist chalking, fading, weathering and has exceptional resistance to UV. All you need to do is ensure the area to be coated is clean, dry and free;from grease

Also available in a non slip-resistant grade: Watco Protecta-Coat

Coverage approx. 30m² per coat. Only a single coat is usually required

Specifications:

Max Operational Temp (deg C) -10
Coverage (m² per litre/kg) 12
Application - Curing Time (hours) light traffic in 6-8 hours, heavy traffic in 12 hours at 20°C
Application - Recommended Coats 1
Coverage 30m² per 2.5L
Max Application Temperature (deg C) 30
Min Application Temperature (deg C) -10

How To Apply:

Substrates:
Protecta-Coat can be used over most existing paint coatings, although a sample area should be tested first if in doubt. Protecta-Coat will also cope with slight movement in an existing coating, and is therefore fine to overcoat asphalt coatings and areas around vibrating machinery for instance.

Surface Preparation:
Floor temperature must be above -10°C and dry. Existing floor paint finishes must be sound and grease and oil should be removed with Watco Bio-D (or similar emulsifying degreasant). It is important that this is thoroughly washed off and the floor is allowed to dry. A good sweep or mechanical brushing is generally regarded as sufficient in these circumstances. If applying outside do not apply when rain is forecast.

Mixing:
Mix between 10°C-25°C. Remove the two tins from the large outer tin. Stir each tin individually and pour into larger outer tin. (Ensure that tin contents are completely emptied by scraping the sides etc).

You can now add the aggregate.

Mix the components together thoroughly using a spatula or wide bladed tool. Continue mixing until an even blend/consistency is obtained. Do not mix more than one tin at a time. If a mixing blade and electric drill are used, also use a spatula to ensure any unmixed material from sides/corners and bottom of the tin is not missed. Do not dilute. The product will last for 25-30 minutes at 15°C. Less at higher temperatures.

Application:
Apply between -10°C and +30°C. The viscosity will become somewhat thicker when applied at temperatures below 0°C and may result in a slight loss of coverage. When mixed a short pile roller should be used to work the product to around or over a 30m² area. This product is designed and performs best when applied very thinly (50 microns). If applied too thickly curing problems can occur.

Curing Times:
Times are dependent on site conditions, but the following can be used as a guide: 
20°C 5°C 0°C -10°C
Recoatable 4-5 hrs 10-12 hrs 16 hrs 30 hrs
Light Traffic 6-8 hrs 18 hrs 24 hrs 36 hrs
Heavy Traffic 12 hrs 24 hrs 36 hrs 48 hrs

 

Write a review

Note: HTML is not translated!
    Bad           Good

Anti Slip Clear Sealer 2.5L Mid Gloss Finish Floor Sealer

  • Product Code: st97
  • Availability: In Stock
  • £175.25
  • Ex Tax: £146.04

Available Options